HTA125A Audio Power Amplifier 125-Watt by Bogen Communications

HTA125A Audio Power Amplifier 125-Watt by Bogen Communications

Model #HTA125A

Regular Price: $1,386.02

Special Price $727.66

Product Overview



  • Multiple output voltages/impedances available

  • Automatic overload protection

  • Listed to UL Standard 60065 for US and Canada

  • Power MOSFET circuitry

  • Capable of continuous operation at rated output power

  • Frequency response ±1dB, 20 to 20,000 Hz at full rated output

  • Distortion less than 0.5% THD, 20 to 20,000 Hz

Details

The HTA125A Audio Power Amplifier 125-Watt by Bogen Communications is a high performance unit with Power MOSFET technology, making them ideally suited to power amplifier design, providing far superior performance and reliability compared to other types of transistors.

They offer high efficiency, reduced heat, simpler overall design, reduced size and weight. The HTA125A Model supplies 125 watts (RMS continuous output) at less than 0.5% total harmonic distortion from 20 to 20,000 Hz. An input signal of only 500mV is required for full rated output.

The input impedances are: high-impedance (50k ohms) unbalanced; low impedance (500/600 ohms, balanced or unbalanced) with optional accessory transformer Model TL600. Line bridging can be achieved with the optional transformer Model TL100. Residual hum and noise is at least 90 dB below rated output and the output regulation is better than 2 dB from no load to full load.

SPECIFICATIONS

  • Dimensions (without removable feet): 19" W x 5-1/4" H x 11" D (48.3 x 13.3 x 27.9 cm)
  • Front Panel Dimensions: 19" W x 5-1/4" H (48.3 x 13.3 cm)
  • Weight: 36 lb. (16.3 kg)
  • Output Loads: 4 ohms, 8 ohms, 25V, 25VCT, 70V
  • Output Regulation: Better than 2 dB from no load to full load
  • Input Impedances: Hi-Z, 50k ohms unbalanced; Lo-Z, 600 ohms, balanced or unbalanced, and 1:1 bridging with optional plug-in transformers
  • Low-Cut Filter: -10 dB @ 100 Hz
  • Controls & Indicators: Front Panel — Illuminated On/Off power switch and overload shutdown LED Rear Panel — Input level control, Slo-Blo fuse Internal — Low-Cut filter switch
  • Power Requirements: 120V ~, 60 Hz, 3.1A, 260 watts @ Full Rated Output (Idle 45W) 
  • Thermal Emissions (full power): 426.9 BTU/hr.
  • Rated Output Power: 125W
  • Total Harmonic Distortion: Less than 0.5%, 20 to 20,000 Hz at full rated output
  • Frequency Response: ±1dB, 20 to 20,000 Hz at full rated output
  • Input Sensitivity: Hi-Z, 500mV; Lo-Z balanced, with optional transformer,150mV
  • Hum and Noise: 90 dB below rated output
  • Overload Protection: Electronic overload protection Electrical: 4A Slo-Blo Fuse
  • Auxiliary Receptacle (not switched): Three-wire grounded*, 300 watts maximum
  • Regulatory Approvals: Listed to UL Standard 60065 for US and Canada
  • Accessories: Model TL600, 600-ohm line-matching transformer; Model TL100, 1:1 line-matching transformer

*This receptacle will be grounded only if the power amplifier has been grounded properly

Additional Information

Promotional Message Switchable to 25V, 70V, 4 ohm and 8 ohm settings
SKU HTA125A
Mount Type No

Write Your Own Review

You're reviewing: HTA125A Audio Power Amplifier 125-Watt by Bogen Communications