HTA250A Audio Power Amplifier 250-Watt by Bogen Communications

HTA250A Audio Power Amplifier 250-Watt by Bogen Communications

Model #HTA250A

Regular Price: $2,312.31

Special Price $1,213.97

Product Overview


  • Power MOSFET circuitry

  • Capable of continuous operation at rated output power

  • Frequency response ±1dB, 20 to 20,000 Hz at full rated output

  • Distortion less than 0.5% THD, 20 to 20,000 Hz

  • Multiple output voltages/impedances available

  • Automatic overload protection

  • Listed to UL Standard 60065 for US and Canada

Details

The HTA250A Audio Power Amplifier 250-Watt by Bogen Communications is a high performance unit with Power MOSFET technology, making it ideally suited to power amplifier design, providing far superior performance and reliability compared to other types of transistors.

The amps can drive a variety of load impedances. Outputs include 4 ohms, 8 ohms, 25VCT and 70 volts. The amplifiers are capable of safely driving any recommended load continuously.

The HTA-Series amps are thermally protected to prevent damage due to excessively high temperatures. Additional failure-preventive devices include overload limiting, short circuit protection, and a SloBlo fuse. Electronic shutdown circuitry is automatically activated if an overload or short occurs and the front panel overload shutdown LED illuminates. Once the cause has been rectified, the unit automatically resets.

 

SPECIFICATIONS

  • Dimensions (without removable feet): 19" W x 5-1/4" H x 11" D (48.3 x 13.3 x 27.9 cm)
  • Front Panel Dimensions: 19" W x 5-1/4" H (48.3 x 13.3 cm)
  • Weight: 50 lb. (22.7 kg)
  • Rated Output Power: 250W
  • Total Harmonic Distortion: Less than 0.5%, 20 to 20,000 Hz at full rated output
  • Frequency Response: ±1dB, 20 to 20,000 Hz at full rated output
  • Input Sensitivity: Hi-Z, 500mV; Lo-Z balanced, with optional transformer,150mV
  • Hum and Noise: 90 dB below rated output
  • Output Loads: 4 ohms, 8 ohms, 25V, 25VCT, 70V
  • Output Regulation: Better than 2 dB from no load to full load
  • Input Impedances: Hi-Z, 50k ohms unbalanced; Lo-Z, 600 ohms, balanced or unbalanced, and 1:1 bridging with optional plug-in transformers
  • Low-Cut Filter: -10 dB @ 100 Hz
  • Controls & Indicators: Front Panel — Illuminated On/Off power switch and overload shutdown LED Rear Panel — Input level control, Slo-Blo fuse Internal — Low-Cut filter switch
  • Power Requirements: 120V ~, 60 Hz, 5.5A, 520 watts @ Full Rated Output (Idle 60W)
  • Thermal Emissions (full power): 939.2 BTU/hr
  • Overload Protection: Electronic overload protection Electrical: 4A Slo-Blo Fuse
  • Auxiliary Receptacle (not switched): Three-wire grounded*, 300 watts maximum
  • Regulatory Approvals: Listed to UL Standard 60065 for US and Canada
  • Accessories: Model TL600, 600-ohm line-matching transformer; Model TL100, 1:1 line-matching transformer

*This receptacle will be grounded only if the power amplifier has been grounded properly

Additional Information

Promotional Message Switchable to 25V, 70V, 4 and 8 Ohm settings.
SKU HTA250A
Mount Type No

Write Your Own Review

You're reviewing: HTA250A Audio Power Amplifier 250-Watt by Bogen Communications